- Home


Air Conditioners | Dehumidifiers | Dishwashers | Disposals | Dryers | Freezers | Humidifiers | Ice Makers | Microwave Ovens | Ovens, Ranges, Stoves | Refrigerators | Trash Compactors | Washers | Water Filters

FAQs | Contact | Apprenticeship | Parts | Model Number Help | Newsletter | Beer
- > Do-It-Yourself Appliance Repair Help > The Kitchen Appliance Repair Forum > DD603 stops mid cycle....problem is not the prism

Find Appliance Parts & Diagrams Here
Enter a model number, part number, type of appliance, brand, or even a part description.

365-day return policy on all parts ordered through this site!


 Moderated by: BrntToast, RegUS_PatOff, appl.tech.29501 Search Our Sites for More Info!
New Topic Reply Printer Friendly
DD603 stops mid cycle....problem is not the prism  Rating:  Rating
AuthorPost
 Posted: Sun Nov 21st, 2010 02:43 pm
  PM Quote Reply
1st Post
Crosby87
Grasshopper
 

Joined: Fri Apr 30th, 2010
Location:  
Posts: 9
Flavorite Brew: molson
Status: 
Offline
I had the broken clip/prism problem with my DD603 which caused the top drawer to stop mid cycle.  I fixed this issue and all was working fine......

But now the top drawer stops at minute 35-36 and shows no error codes.  I press start and it picks up where it left off and finishes the cycle.

So far, it has only done this when both top and bottom run at the same time.

What else could have gone bad?  Heater plate?  Controller?  How to diagnose if no error codes? 

thank you, wise members of this board!

Back To Top PM Quote Reply  

 Posted: Sun Nov 21st, 2010 02:51 pm
  PM Quote Reply
2nd Post
Crosby87
Grasshopper
 

Joined: Fri Apr 30th, 2010
Location:  
Posts: 9
Flavorite Brew: molson
Status: 
Offline
edit--I just paused the drawer at minute 28 and it seemed plenty hot...steam came pouring out so it is heating up

Back To Top PM Quote Reply

 Posted: Sun Nov 21st, 2010 03:15 pm
  PM Quote Reply
3rd Post
Crosby87
Grasshopper
 

Joined: Fri Apr 30th, 2010
Location:  
Posts: 9
Flavorite Brew: molson
Status: 
Offline
edit--sorry, one more thing. the top drawer already has the metal hose carrier/linkage

Back To Top PM Quote Reply  

 Posted: Sun Nov 21st, 2010 11:23 pm
  PM Quote Reply
4th Post
Crosby87
Grasshopper
 

Joined: Fri Apr 30th, 2010
Location:  
Posts: 9
Flavorite Brew: molson
Status: 
Offline
update-I took the front panel off (again). My Gorilla tape is holding strong, but now the top clip on the controller is broken. The plastic is almost brittle. I re-positioned and re-secured everything so lets see what happens..

strange that it has stopped twice now, and it was at minute 35-36 each time.

could this be anything else?

this will be my last fisher/paykel product for sure!

Back To Top PM Quote Reply

 Posted: Mon Nov 22nd, 2010 05:03 am
  PM Quote Reply
5th Post
Crosby87
Grasshopper
 

Joined: Fri Apr 30th, 2010
Location:  
Posts: 9
Flavorite Brew: molson
Status: 
Offline
update yet again-this time it stopped at minute 107 (on a reg 115 min normal cycle). only the top drawer was on. no error codes. I unlocked the key pad and pressed start and it fired right up again.

I'm thinking the controller is the problem. how to confirm?

Back To Top PM Quote Reply  

Current time is 05:08 am Tell a friend about this page... all your other friends are doing it!  
- > Do-It-Yourself Appliance Repair Help > The Kitchen Appliance Repair Forum > DD603 stops mid cycle....problem is not the prism Top



Find Appliance Parts & Diagrams Here
Enter a model number, part number, type of appliance, brand, or even a part description.

365-day return policy on all parts ordered through this site!

FAQs | Contact | Apprenticeship | Parts | Model Number Help | Newsletter | Beer

Your Sometimes-Lucid Host:
- Home
"If I can't help you fix your appliance and make you 100% satisfied, I will come to your home and slice open my belly, spilling my steaming entrails onto your floor."


UltraBB 1.17 Copyright © 2007-2008 Data 1 Systems
Page processed in 0.1094 seconds (38% database + 62% PHP). 26 queries executed.

Web Analytics