|
|
Air Conditioners | Dehumidifiers | Dishwashers | Disposals | Dryers | Freezers | Humidifiers | Ice Makers | Microwave Ovens | Ovens, Ranges, Stoves | Refrigerators | Trash Compactors | Washers | Water Filters |
|
FAQs | Contact | Apprenticeship | Consultations | Parts | Model Number Help | Newsletter | Beer | Fixitnow.com
|
ApplianceGuru.com: The Samurai Appliance Repair Forums > Do-It-Yourself Appliance Repair Help > The Laundry Appliance Repair Forum > Whirlpool 3-speed motor wiring |
|
| Moderated by: RegUS_PatOff, BrntToast, appl.tech.29501 | Search Our Sites for More Info! |
|
|||||||||||||
| Whirlpool 3-speed motor wiring | Rate Topic |
| Author | Post |
|---|
| Posted: Fri Mar 7th, 2008 11:47 pm |
|
1st Post |
|
GNBrews Senior Apprentice Appliantologist
|
I picked-up a P/n: 3352287 3-speed motor off eBay, and would like to use it to run a meat grinder. Would any of you fellas happen to know what wires on the harness I have to provide juice to run at the 3 different speeds (1725/1140/850)? EDIT: I'm mostly only interested in the 1725RPM mode, but would like information on the other speeds for possible use later. I did also find a wiring diagram for a Neptune model that uses this motor, but I'm not sure I understand how each "P" portion interacts.  http://www.servicematters.com/docs/wiring/Wiring%20Sheet%20-%203954488.pdf Thanks! Last edited on Sat Mar 8th, 2008 01:02 am by GNBrews |
||||||||||||||
| |||||||||||||||
| Posted: Sat Mar 8th, 2008 08:12 am |
|
2nd Post |
|
RegUS_PatOff Fellow, Academy of Sublime Masters of Appliantology 
|
I wouldn't advise modifing a meat grinder. You would need a safety stop/disconnect accessible to the operator. You would need an ON/OFF switch and a 3 position switch for the speeds (4P, 6P, 8P) and a push to start button (4P AUX) for the start switch in series with a AC start capacitor. 324-389MFD 110V AC click on picture  Last edited on Tue Mar 11th, 2008 01:01 am by RegUS_PatOff ____________________ The new repair forums==> http://appliantology.org RegUS_PatOff http://www.youtube.com/watch?v=oPAY2LsKVEw my video production: “Easter Seals Walk With Me” http://www.youtube.com/watch?v=-EBiLyYXMiA |
|||||||||||||
| ||||||||||||||
| Posted: Sat Mar 8th, 2008 05:38 pm |
|
3rd Post |
|
GNBrews Senior Apprentice Appliantologist
|
Thanks Reg; I realize that in todays blameless society, such disclaimers are necessary. I am a resposible adult and understand that meat grinders will grind my appendages just as easily as anything else.  The motor came supplied with its starting capacitor, so a replacement will not be necessary. I've got a factory harness with leg wires that plugs into the motor switch (red - FSP 62850 on top of the motor). I'll forgo the other speeds for simplicity and only need information on how to energize the (8P) section and how to start it. 
|
||||||||||||||
| |||||||||||||||
| Posted: Mon Mar 10th, 2008 04:05 am |
|
4th Post |
|
GNBrews Senior Apprentice Appliantologist
|
No ideas guys/gals? Basically, if I wanted to test this motor to see if it works (by giving it current), how would I do that?
|
|||||||||||||
| ||||||||||||||
| Posted: Mon Mar 10th, 2008 12:46 pm |
|
5th Post |
|
RegUS_PatOff Fellow, Academy of Sublime Masters of Appliantology
|
white & yellow wires go to neutral blue (hi-speed) goes to switched power black goes through capacitor and through start switch to power Last edited on Mon Mar 10th, 2008 12:47 pm by RegUS_PatOff ____________________ The new repair forums==> http://appliantology.org RegUS_PatOff http://www.youtube.com/watch?v=oPAY2LsKVEw my video production: “Easter Seals Walk With Me” http://www.youtube.com/watch?v=-EBiLyYXMiA |
||||||||||||||
| |||||||||||||||
| Posted: Tue Mar 11th, 2008 12:21 am |
|
6th Post |
|
GNBrews Senior Apprentice Appliantologist
|
Thanks again Reg! So, the field winding needs to be energized (blue wire) before the start circuit is energized? Then, once the motor is running, the start circuit can be disconnected? Or is the start circuit automatically disconnected by the centrifugal switch?
|
|||||||||||||
| ||||||||||||||
| Posted: Tue Mar 11th, 2008 12:47 am |
|
7th Post |
|
RegUS_PatOff Fellow, Academy of Sublime Masters of Appliantology
|
the start winding would be automatically disconnected by the centrifugal switch if it's part of the motor. Some motors it's a separate switch mounted on the motor.... ooh.. I see your message that it came with the switch. click on picture  OK, neutral goes to white & yellow wires. switched power goes to blue (hi-speed) & through capacitor to the centrifugal switch (Red connection). Last edited on Tue Mar 11th, 2008 01:15 am by RegUS_PatOff ____________________ The new repair forums==> http://appliantology.org RegUS_PatOff http://www.youtube.com/watch?v=oPAY2LsKVEw my video production: “Easter Seals Walk With Me” http://www.youtube.com/watch?v=-EBiLyYXMiA |
||||||||||||||
| |||||||||||||||
| Posted: Wed Mar 12th, 2008 06:13 pm |
|
8th Post |
|
GNBrews Senior Apprentice Appliantologist
|
Thanks again for all your help, Reg! The capacitor popped, but I think it was faulty (internal short). I'll have to pick-up a new one from the surplus center. The motor did run though.
|
|||||||||||||
| ||||||||||||||
| Posted: Wed Mar 12th, 2008 06:16 pm |
|
9th Post |
|
RegUS_PatOff Fellow, Academy of Sublime Masters of Appliantology
|
OK, make sure it's an AC start capacitor of similar ratings Last edited on Wed Mar 12th, 2008 06:30 pm by RegUS_PatOff ____________________ The new repair forums==> http://appliantology.org RegUS_PatOff http://www.youtube.com/watch?v=oPAY2LsKVEw my video production: “Easter Seals Walk With Me” http://www.youtube.com/watch?v=-EBiLyYXMiA |
||||||||||||||
| |||||||||||||||
| Posted: Tue Apr 15th, 2008 02:20 am |
|
10th Post |
|
genoreno Senior Apprentice Appliantologist
|
Reg, I just picked up a junk Whirlpool washer that was set on the curb for Spring Cleanup. I salvaged the motor (the same one in this thread) for a project and wired it just as you said earlier in this thread. The motor works great. I'm just wondering... if blue is the high speed, what wire is the low speed one. The only other color wire on the harness is orange, and it doesn't appear that there is a wire that connects to that pin in the plug and goes down into the motor like the blue one did. The only other wires that are unused that go from the plug down into the motor are brown and black. Are these different speeds (similar to the blue) also? Thanks, Gene
|
|||||||||||||
| ||||||||||||||
| Posted: Tue Apr 15th, 2008 02:41 am |
|
11th Post |
|
RegUS_PatOff Fellow, Academy of Sublime Masters of Appliantology
|
if it's the same motor: as shown in the OP's first message PDF: High speed = Blue Med speed = White / Violet Low speed = White / Orange Start = Black Start = yellow Neutral = White
____________________ The new repair forums==> http://appliantology.org RegUS_PatOff http://www.youtube.com/watch?v=oPAY2LsKVEw my video production: “Easter Seals Walk With Me” http://www.youtube.com/watch?v=-EBiLyYXMiA |
||||||||||||||
| |||||||||||||||
| Posted: Tue Apr 15th, 2008 10:35 am |
|
12th Post |
|
Moostafa The Ayatollah of Appliantology 
|
Hello, my salvaging friend. May Allah grant that this picture will assist you in your motor replacement efforts.
____________________ Allahu Akbar! Moostafa |
|||||||||||||
| ||||||||||||||
Current time is 02:04 am
|
|
| ApplianceGuru.com: The Samurai Appliance Repair Forums > Do-It-Yourself Appliance Repair Help > The Laundry Appliance Repair Forum > Whirlpool 3-speed motor wiring | Top |
| Find Appliance Parts & Diagrams Here |
| Enter a model number, part number, type of appliance, brand, or even a part description. |
|
365-day return policy on all parts ordered through this site! |
FAQs | Contact | Apprenticeship | Consultations | Parts | Model Number Help | Newsletter | Beer | Fixitnow.com
