 |
PM |  | |
Quote | | |
Reply | | |
Full Topic | |
| Joined: | Sat Jun 25th, 2005 |
| Location: | USA |
| Posts: | 271 |
| Status: |
Offline
|
I hope this helps this needs to be a sticky this covers all THERMADOR COOKING PRODUCTS
Thermador
HOW TO INTERPRET CODES
When a fault occurs, the control will flash the blue oven “on light” and the Blue “heating light” sequentially to
indicate the fault. The fault codes have two numbers, these numbers are interpreted by the number of times the
lights flash. The oven “on light” will flash indicating the first number, and the “heating light” will flash indicating
the second number.
EXAMPLE:
Error E9 is…. No Cooling Fans. The code is 43. The oven “on light” will flash four times, then the “heating light”
will flash three times, then pause. The sequence will then repeat as long as the fault is present.
EMERSON APPLIANCE CONTROLS DOCUMENT: 92S21720100
DIVISION OF EMERSON ELECTRIC CO. REVISION:B
Product Specification for Sago Oven Control PAGE:
13. DIAGNOSTIC CODES
DeBounce is the Rate at which the error checking occurs13.1 Diagnostic Code Checking
The following chart describes the Fault code structure for the Control.
Alarm fault monitor is always active. Any oven cancel key will reset
the display to TOD
idle.
CODE DESCRIPTION WHEN CHECKED DEBOUNCE ERROR
MESSAGE
DISPLAYED
ACTION
TAKEN BY
CONTROL
F13 Upper oven RTD not calibrated Always 10 seconds Message 1 Cancel
cooking/timing
functions
F14 Display board EEPROM error Oven Programming 5 tries Message 1 Cancel
cooking/timing
functions
F19 Power board Communication error Always 20 seconds Message 1 Cancel
cooking/timing
functions
F23 Keyboard gain unstable
Keyboard scratches
Loose molex or pins, air pocket in
control
Always 20 seconds Message 1 Cancel
cooking/timing
functions
F24 Keyboard disconnected Always 20 seconds Message 1 Cancel
cooking/timing
functions
F25 Keys stuck Always 20 seconds Message 1 Cancel
cooking/timing
functions
F26 Keys moving/dropping out Always 20 seconds Message 1 Cancel
cooking/timing
functions
F30 Upper oven sensor shorted Always 20 seconds Message 1 Cancel
cooking/timing
functions
F31 Upper oven sensor open Always 20 seconds Message 1 Cancel
cooking/timing
functions
F32 Upper oven over temperature while
cleaning
Cleaning 20 seconds Message 1 Cancel
cooking/timing
functions
F33 Upper oven over temperature while Non-Clean 20 seconds Message 1 Cancel
cooking cooking/timing
functions
F34 Upper oven cooling fan over-speed or
under-speed detected
Cooking 1 minute Message 1 Cancel
cooking/timing
functions
F40 Upper oven meat probe shorted Cooking 20 seconds Message 1 Cancel
cooking/timing
functions
F41 Upper oven meat probe not calibrated Always 10 seconds Message 1 Cancel
cooking/timing
functions
F43 Lower oven RTD not calibrated Always 10 seconds Message 1 Cancel
cooking/timing
functions
F50 Upper oven door latch signal shorted low Always 1 minute Message 1 Cancel
cooking/timing
functions
F51 Upper oven door latch stuck unlocked Cooking/ Cleaning 1 minute Message 1 Cancel
cooking/timing
functions
F52
Upper oven door position error Cooking/ Cleaning 1 minute Message 1 Cancel
cooking/timing
functions
F53
Upper oven door latch stuck locked Non-Clean 1 minute Message 1 Cancel
cooking/timing
functions
F54
Upper oven latch input shorted Cleaning 1 minute Message 1 Cancel
cooking/timing
functions
F60
Lower oven sensor shorted Always 20 seconds Message 1 Cancel
cooking/timing
functions
F61
Lower oven sensor open Always 20 seconds Message 1 Cancel
cooking/timing
functions
F62
Lower oven over temperature while
cleaning
Cleaning 20 seconds Message 1 Cancel
cooking/timing
functions
F63
Lover oven over temperature while
cooking
Non-Clean 20 seconds Message 1 Cancel
cooking/timing
functions
F64
Lower oven cooling fan over-speed or
under-speed detected
Cooking 1 minute Message 1 Cancel
cooking/timing
functions
F70
Lover oven meat probe shorted Cooking 20 seconds Message 1 Cancel
cooking/timing
functions
EMERSON APPLIANCE CONTROLS DOCUMENT: 92S21720100
DIVISION OF EMERSON ELECTRIC CO. REVISION:B
Product Specification for Sago Oven Control PAGE:
13. DIAGNOSTIC CODES DeBounce is the Rate at which the error checking occurs
13.1 Diagnostic Code Checking
The following chart describes the Fault code structure for the Control.
Alarm fault monitor is always active. Any oven cancel key will reset
the display to TOD idle.
CODE DESCRIPTION WHEN CHECKED DEBOUNCE ERROR
MESSAGE
DISPLAYED
ACTION
TAKEN BY
CONTROL
F13 Upper oven RTD not calibrated Always 10 seconds Message 1 Cancel
cooking/timing
functions
F14 Display board EEPROM error Oven Programming 5 tries Message 1 Cancel
cooking/timing
functions
F19 Power board Communication error Always 20 seconds Message 1 Cancel
cooking/timing
functions
F23 Keyboard gain unstable
Keyboard scratches
Loose molex or pins, air pocket in
control
Always 20 seconds Message 1 Cancel
cooking/timing
functions
F24 Keyboard disconnected Always 20 seconds Message 1 Cancel
cooking/timing
functions
F25 Keys stuck Always 20 seconds Message 1 Cancel
cooking/timing
functions
F26 Keys moving/dropping out Always 20 seconds Message 1 Cancel
cooking/timing
functions
F30 Upper oven sensor shorted Always 20 seconds Message 1 Cancel
cooking/timing
functions
F31 Upper oven sensor open Always 20 seconds Message 1 Cancel
cooking/timing
functions
F32 Upper oven over temperature while
cleaning
Cleaning 20 seconds Message 1 Cancel
cooking/timing
functions
F33 Upper oven over temperature while Non-Clean 20 seconds Message 1 Cancel
____________________
outerspace holds the key to the biggest mystery in the universe . where do women come from ?
Currently serving SPEED QUEEN , HUEBSCH