|
|
Air Conditioners | Dehumidifiers | Dishwashers | Disposals | Dryers | Freezers | Humidifiers | Ice Makers | Microwave Ovens | Ovens, Ranges, Stoves | Refrigerators | Trash Compactors | Washers | Water Filters |
|
FAQs | Contact | Apprenticeship | Consultations | Parts | Model Number Help | Newsletter | Beer | Fixitnow.com
|
ApplianceGuru.com: The Samurai Appliance Repair Forums > Do-It-Yourself Appliance Repair Help > The Laundry Appliance Repair Forum > Fisher & Paykel slow fill |
|
| Moderated by: RegUS_PatOff, BrntToast, appl.tech.29501 | Search Our Sites for More Info! |
|
|||||||||||||
| Fisher & Paykel slow fill | Rate Topic |
| Author | Post |
|---|
| Posted: Sat Apr 2nd, 2005 12:13 pm |
|
1st Post |
|
kevvie Grasshopper
|
I have a GW501 washer, now 12 years old. It has started to fill up very s-l-o-w-l-y, to the point of being unusable. I have checked all filters, they are ok. The resistance of the solenoids reads at 15 Ohms for each, so I assume the problem is elsewhere - especially since both hot and cold water are equally slow. I've seen some discussion on this topic at http://fixitnow.com/2004/10/appliance-repair-revelation-fisher_30.htm and am guessing it is the power control and pressure sensing module, but the online parts supplier doesn't seem to have a part with that description - closest is http://spares.alliedappliance.com.au/search.php?match=&keyword_list=gw501+power+control&x=33&y=8 Any suggestions? (either part names or what the problem might be) Thanks, Kev.
|
||||||||||||||
| |||||||||||||||
| Posted: Sat Apr 2nd, 2005 12:19 pm |
|
2nd Post |
|
Samurai Appliance Repair Man Fermented Grand Master of Appliantology 
|
Are you on a well? If so, and given the age of the washer, it's likely the valve assembly needs to be replaced. What you're describing is ezzacly what happens when sediment from a well gets into the valve and gunks it up. Also, check your water pressure at the hose. If you filter screens in either end of the hose, remove and/or replace them. Buy your parts directly from Fisher-Paykel. You'll get a better price and you know you'll be getting a genuine replacment part.
____________________ To ask a question, use our new forums==> http://appliantology.org 365-Day No-Hassle Return Policy on all parts purchased through this site, even electrical parts that have been installed! |
|||||||||||||
| ||||||||||||||
| Posted: Sat Apr 2nd, 2005 01:30 pm |
|
3rd Post |
|
kevvie Grasshopper
|
Thanks for the reply. No wells anywhere near me, we have a good clean soft water supply. I have checked the hoses, good pressure all the way through, and disassembled everything to the solenoid to make sure there were no signs of any gunk. In fact they were all spotless. Since we only ever have used cold water in the machine, and the problem exists equally for the hot and cold water, and the solenoids read ok from a resistance perspective, I am assuming it is the control board. Which I have since found out is $230 for a reconditioned one. If I did have to replace the inlet valves, that comes to $94. And the pump is on it's way out, which is $76 I know will be coming along soon. Methinks it is time to cave in to the boss of the house and buy a new machine (which is bigger as well)..... Cheers, Kevin.
|
||||||||||||||
| |||||||||||||||
| Posted: Sat Apr 2nd, 2005 01:58 pm |
|
4th Post |
|
Samurai Appliance Repair Man Fermented Grand Master of Appliantology
|
No need to guess about it: an easy check would be to measure the supply voltage at the water inlet valve solenoid terminals. If you're getting junk voltage then, yepper, you got yer self a bad control board. Voltage good? Then the valve is trash. Slam dunk. And who charges $94 for a valve!? Sounds like I've been drastically undercharging and leaving money on the table! 
____________________ To ask a question, use our new forums==> http://appliantology.org 365-Day No-Hassle Return Policy on all parts purchased through this site, even electrical parts that have been installed! |
|||||||||||||
| ||||||||||||||
| Posted: Sun Apr 3rd, 2005 12:42 am |
|
5th Post |
|
The Seven Master Appliantologist
|
kevvie wrote:Since we only ever have used cold water in the machine, and the problem exists equally for the hot and cold water, and the solenoids read ok from a resistance perspective, I am assuming it is the control board. Which I have since found out is $230 for a reconditioned one. If I did have to replace the inlet valves, that comes to $94. And the pump is on it's way out, which is $76 I know will be coming along soon. The website is in Australia. So the price quoted should be in Aust $. The website states that these soleniods (COLD and HOT inlets) are 12V. But it does not tell us whether it is 12Vdc or 12Vac. So you might have to use the multi-meter wisely. You could test and operate the soleniods if you have the correct external 12V sourve.
____________________ The Seven |
||||||||||||||
| |||||||||||||||
| Posted: Tue Apr 5th, 2005 01:03 pm |
|
6th Post |
|
kevvie Grasshopper
|
That's a good point. I put the meter on the solenoids with the following results: COLD WASH: cold terminals 12V. hot terminals 0V WARM WASH: cold terminals 12V. hot terminals 7.6V HOT WASH: cold terminals 12V. hot terminals 12V So I guess that means the controller board is working and I have two faulty solenoids. Funny that the cold one is more expensive ($AU57) than the hot one ($AU37) but I'm sure the spare parts pricing guys had a good reason. Looks like it lives for a little longer yet. Thanks for the help. 
|
|||||||||||||
| ||||||||||||||
| Posted: Tue Apr 5th, 2005 04:43 pm |
|
7th Post |
|
Samurai Appliance Repair Man Fermented Grand Master of Appliantology
|
Glad to help. Nice troubleshootin', Hoss! 
____________________ To ask a question, use our new forums==> http://appliantology.org 365-Day No-Hassle Return Policy on all parts purchased through this site, even electrical parts that have been installed! |
||||||||||||||
| |||||||||||||||
Current time is 12:34 am
|
|
| ApplianceGuru.com: The Samurai Appliance Repair Forums > Do-It-Yourself Appliance Repair Help > The Laundry Appliance Repair Forum > Fisher & Paykel slow fill | Top |
| Find Appliance Parts & Diagrams Here |
| Enter a model number, part number, type of appliance, brand, or even a part description. |
|
365-day return policy on all parts ordered through this site! |
FAQs | Contact | Apprenticeship | Consultations | Parts | Model Number Help | Newsletter | Beer | Fixitnow.com
