|
|
Air Conditioners | Dehumidifiers | Dishwashers | Disposals | Dryers | Freezers | Humidifiers | Ice Makers | Microwave Ovens | Ovens, Ranges, Stoves | Refrigerators | Trash Compactors | Washers | Water Filters |
|
FAQs | Contact | Apprenticeship | Consultations | Parts | Model Number Help | Newsletter | Beer | Fixitnow.com
|
ApplianceGuru.com: The Samurai Appliance Repair Forums > Do-It-Yourself Appliance Repair Help > The Laundry Appliance Repair Forum > Whirlpool GGW9250PW0 Diagnostic question |
|
| Moderated by: RegUS_PatOff, BrntToast, appl.tech.29501 | Search Our Sites for More Info! | Page: 1 2 3 4   |
|
||||||||||||
| Whirlpool GGW9250PW0 Diagnostic question | Rate Topic |
| Author | Post |
|---|
| Posted: Fri Sep 4th, 2009 02:10 pm |
|
1st Post |
|
joetry Merit Apprentice Appliantologist
|
Reading all other post on this fine dryer with similar questions "spin but no heat" In normal mode I do not have power to the blower, centrifugal switch.... all other components ohm out at right levels.. I have not seen this question... when I put the dryer in diag mode it works fine... Looking at tech sheet and the limited info on teh control board, I am trying to figure out what the heck is by-passed in diag mode... thoughts suggestions... beside buy simple... Thank in advance... Joe
____________________ jl |
||||||||||||||
| |||||||||||||||
| Posted: Fri Sep 4th, 2009 07:31 pm |
|
2nd Post |
|
RegUS_PatOff Fellow, Academy of Sublime Masters of Appliantology 
|
any Error Codes ? GGW9250PW0 Tech Sheets
____________________ The new repair forums==> http://appliantology.org RegUS_PatOff http://www.youtube.com/watch?v=oPAY2LsKVEw my video production: “Easter Seals Walk With Me” http://www.youtube.com/watch?v=-EBiLyYXMiA |
|||||||||||||
| ||||||||||||||
| Posted: Fri Sep 4th, 2009 07:45 pm |
|
3rd Post |
|
joetry Merit Apprentice Appliantologist
|
No error codes.
____________________ jl |
||||||||||||||
| |||||||||||||||
| Posted: Fri Sep 4th, 2009 09:07 pm |
|
4th Post |
|
RegUS_PatOff Fellow, Academy of Sublime Masters of Appliantology
|
joetry wrote: ... I do not have power to the blower, centrifugal switch.... Blower ?? ... mechanically driven by Drum Motor Centrifufal Switch ... closes when Drum Motor is turning ..
____________________ The new repair forums==> http://appliantology.org RegUS_PatOff http://www.youtube.com/watch?v=oPAY2LsKVEw my video production: “Easter Seals Walk With Me” http://www.youtube.com/watch?v=-EBiLyYXMiA |
|||||||||||||
| ||||||||||||||
| Posted: Fri Sep 4th, 2009 09:11 pm |
|
5th Post |
|
joetry Merit Apprentice Appliantologist
|
Ok.. now I am confused... Replaced the controller board.. have fire but no motor... put old board back in an have fire no spin...
____________________ jl |
||||||||||||||
| |||||||||||||||
| Posted: Fri Sep 4th, 2009 09:19 pm |
|
6th Post |
|
RegUS_PatOff Fellow, Academy of Sublime Masters of Appliantology
|
joetry wrote: .. have fire but no motor... put old board back in an have fire no spin... same thing ? shouldn't have fire without Motor Spin (Motor Centrifugal Switch)
____________________ The new repair forums==> http://appliantology.org RegUS_PatOff http://www.youtube.com/watch?v=oPAY2LsKVEw my video production: “Easter Seals Walk With Me” http://www.youtube.com/watch?v=-EBiLyYXMiA |
|||||||||||||
| ||||||||||||||
| Posted: Fri Sep 4th, 2009 09:22 pm |
|
7th Post |
|
joetry Merit Apprentice Appliantologist
|
Are you suggesting the centrifugal switch? I agree no spin no fire... When I first try to start it I get belt error.. because belt is off.. I left the belt arm up, here it click and ignitor starts no spin... feel like I have walked into the swamp and the alligators are swarming...
____________________ jl |
||||||||||||||
| |||||||||||||||
| Posted: Fri Sep 4th, 2009 09:22 pm |
|
8th Post |
|
joetry Merit Apprentice Appliantologist
|
any thoughts on testing the certrigfigual switch...
____________________ jl |
|||||||||||||
| ||||||||||||||
| Posted: Fri Sep 4th, 2009 09:26 pm |
|
9th Post |
|
RegUS_PatOff Fellow, Academy of Sublime Masters of Appliantology
|
Ohm the Switch (as shown in the Wiring Diagram) while the Dryer is not running
____________________ The new repair forums==> http://appliantology.org RegUS_PatOff http://www.youtube.com/watch?v=oPAY2LsKVEw my video production: “Easter Seals Walk With Me” http://www.youtube.com/watch?v=-EBiLyYXMiA |
||||||||||||||
| |||||||||||||||
| Posted: Fri Sep 4th, 2009 09:33 pm |
|
10th Post |
|
joetry Merit Apprentice Appliantologist
|
ok
____________________ jl |
|||||||||||||
| ||||||||||||||
| Posted: Fri Sep 4th, 2009 11:48 pm |
|
11th Post |
NCSU_laundry_tech
|
ohm the thermistor from the board. should be around 10k at room temp
____________________ To alcohol! The cause of... and solution to... all of life's problems. Doc Watson - Shady Grove: http://www.youtube.com/watch?v=b-kaG1NuLZM riding my dirtbike in clayton NC: http://www.youtube.com/watch?v=NnCmY0vzmYM |
||||||||||||||
| |||||||||||||||
| Posted: Sat Sep 5th, 2009 12:40 am |
|
12th Post |
|
joetry Merit Apprentice Appliantologist
|
OK.. all individual components appear to ohm out correct... I am thinking short somewhere...going deeper in the swamp.. gonna hunt and peck until I find the darn thing... any suggestions as where to start...
____________________ jl |
|||||||||||||
| ||||||||||||||
| Posted: Sat Sep 5th, 2009 12:40 am |
|
13th Post |
|
joetry Merit Apprentice Appliantologist
|
OK.. all individual components appear to ohm out correct... I am thinking short somewhere...going deeper in the swamp.. gonna hunt and peck until I find the darn thing... any suggestions as where to start...
____________________ jl |
||||||||||||||
| |||||||||||||||
| Posted: Sat Sep 5th, 2009 01:10 am |
|
14th Post |
NCSU_laundry_tech
|
if there is only one bad component and you have 240 at the terminal block then the bad part is the one with 240 across it when running and set to heat. if the 240 is at the heater relay on the board then the board is bad or its getting a bad reading from the thermistor
____________________ To alcohol! The cause of... and solution to... all of life's problems. Doc Watson - Shady Grove: http://www.youtube.com/watch?v=b-kaG1NuLZM riding my dirtbike in clayton NC: http://www.youtube.com/watch?v=NnCmY0vzmYM |
|||||||||||||
| ||||||||||||||
| Posted: Sat Sep 5th, 2009 01:19 am |
|
15th Post |
|
joetry Merit Apprentice Appliantologist
|
Thanks... I'll give it a look... But a bad reading/thermistor would block ignition and not impact motor operation. Or are you thinking that bad heater relay --> allows fire even without motor spinning.. I appreciate your help and suggestions... Note: new control board and old board are now doing the same... no spin but fire.. original problem was spin but no fire... unless of course I was running in diag mode...than it worked fine...
____________________ jl |
||||||||||||||
| |||||||||||||||
| Posted: Sat Sep 5th, 2009 01:24 am |
|
16th Post |
|
RegUS_PatOff Fellow, Academy of Sublime Masters of Appliantology
|
RegUS_PatOff wrote: ... shouldn't have fire without Motor Spin (Motor Centrifugal Switch) ..
____________________ The new repair forums==> http://appliantology.org RegUS_PatOff http://www.youtube.com/watch?v=oPAY2LsKVEw my video production: “Easter Seals Walk With Me” http://www.youtube.com/watch?v=-EBiLyYXMiA |
|||||||||||||
| ||||||||||||||
| Posted: Sat Sep 5th, 2009 01:32 am |
|
17th Post |
|
joetry Merit Apprentice Appliantologist
|
Tried with second motor/switch... same problem...
____________________ jl |
||||||||||||||
| |||||||||||||||
| Posted: Sat Sep 5th, 2009 02:22 am |
|
18th Post |
|
kdog Fellow, Academy of Sublime Masters of Appliantology 
|
Grounded element?
____________________ Can Ye spare some 'cutter me brutha ? http://web.me.com/zenzoidman/kdog/ |
|||||||||||||
| ||||||||||||||
| Posted: Sat Sep 5th, 2009 02:26 am |
|
19th Post |
|
RegUS_PatOff Fellow, Academy of Sublime Masters of Appliantology
|
joetry wrote: Tried with second motor/switch... same problem... Then the Black Wire from the Motor Centrifugal Switch to the Ignitor, MOV, or Gas Valve Coils, is shorted to ground ... (Gas Dryer) 
____________________ The new repair forums==> http://appliantology.org RegUS_PatOff http://www.youtube.com/watch?v=oPAY2LsKVEw my video production: “Easter Seals Walk With Me” http://www.youtube.com/watch?v=-EBiLyYXMiA |
||||||||||||||
| |||||||||||||||
| Posted: Sat Sep 5th, 2009 03:18 am |
|
20th Post |
|
joetry Merit Apprentice Appliantologist
|
I will test out tomorrow am.... just too darn tired to try anything else... again I appreciate all the guidance and direction...
____________________ jl |
|||||||||||||
| ||||||||||||||
Current time is 03:12 am
|
Page: 1 2 3 4 |
| ApplianceGuru.com: The Samurai Appliance Repair Forums > Do-It-Yourself Appliance Repair Help > The Laundry Appliance Repair Forum > Whirlpool GGW9250PW0 Diagnostic question | Top |
| Find Appliance Parts & Diagrams Here |
| Enter a model number, part number, type of appliance, brand, or even a part description. |
|
365-day return policy on all parts ordered through this site! |
FAQs | Contact | Apprenticeship | Consultations | Parts | Model Number Help | Newsletter | Beer | Fixitnow.com
