| Author | Post |
|---|
edcmaak11
Apprentice Appliantologist
| Joined: | Sat Mar 22nd, 2008 |
| Location: | NYC, New York USA |
| Posts: | 24 |
| Flavorite Brew: | All beers.... |
| Status: |
Offline
|
|
Posted: Mon Sep 29th, 2008 00:27 |
|
I got a Frigidaire model # gltf1040as0 front load washer problem. My daughter was putting the load inside this washer, when she pulled the switch to turn on the washer, it just closed the door and turn on the “door Locked” light. She called me over, I checked the INNER switch Clockwise, it either pours water or drain, but never spins.
I suspect it is the problem with the switch, because it just stay at on point and not going over to other mode(wash, drain, spin). Can anyone help please? Any diagram procedure that I can use to open the washer? Thank You!
Last edited on Mon Sep 29th, 2008 00:34 by edcmaak11
|
NCSU_laundry_tech
Sublime Master of Appliantology
| Joined: | Mon Aug 18th, 2008 |
| Location: | Raleigh, North Carolina USA |
| Posts: | 223 |
| Flavorite Brew: | The one in my hand |
| Status: |
Online
|
|
Posted: Mon Sep 29th, 2008 02:28 |
|
could be motor control board
____________________
To alcohol! The cause of... and solution to... all of life's problems.
Doc Watson - Shady Grove: http://www.youtube.com/watch?v=b-kaG1NuLZM
riding my dirtbike in clayton NC: http://www.youtube.com/watch?v=NnCmY0vzmYM
|
RegUS_PatOff
Fellow, Academy of Sublime Masters of Appliantology
| Joined: | Sat Sep 24th, 2005 |
| Location: | Milwaukee, Wisconsin USA |
| Posts: | 3956 |
| Flavorite Brew: | A & W in a frosted mug |
| Status: |
Online
|
|
Posted: Mon Sep 29th, 2008 03:20 |
|
Drive Motor dosen't turn the Drum at all ?
Page from 5995369211.pdf
GLTF1040AS0 Parts ManualLast edited on Mon Sep 29th, 2008 03:21 by RegUS_PatOff
____________________
RegUS_PatOff http://www.youtube.com/watch?v=oPAY2LsKVEw
my “Easter Seals Walk With Me” video production http://www.youtube.com/watch?v=-EBiLyYXMiA
After leaving this Earth "Do you want the Smoking or Non-Smoking section ?"
|
edcmaak11
Apprentice Appliantologist
| Joined: | Sat Mar 22nd, 2008 |
| Location: | NYC, New York USA |
| Posts: | 24 |
| Flavorite Brew: | All beers.... |
| Status: |
Offline
|
|
Posted: Mon Sep 29th, 2008 04:53 |
|
Thanks for the quick reply. I just took the top and the bottom part out and amazed by the good quality it used. I took the timer out which I belived is the timer, but will test tomorrow for the Motor control board and fuse.
|
edcmaak11
Apprentice Appliantologist
| Joined: | Sat Mar 22nd, 2008 |
| Location: | NYC, New York USA |
| Posts: | 24 |
| Flavorite Brew: | All beers.... |
| Status: |
Offline
|
|
Posted: Wed Oct 8th, 2008 23:34 |
|
RegUS_PatOff wrote: Drive Motor dosen't turn the Drum at all ?
Page from 5995369211.pdf
GLTF1040AS0 Parts Manual
Thanks for the Manual the page. I tested last week and found out Pin 5 (Six Pins) to pins 2,6,10(Ten Pins) reads 124 VAC, but the Pin 5 (six pins) to 1 & 9 (Ten pins) reads 35 - 47 VAC. I ordered the Speed control board. Clean out the coins in the drain, got $1.35 
I got Speed control board yesterday and installed today and works fine on the first load. Little wetter than expected and the Fabric softner was still there after the regular cycle. Second Load, it stop at the middle of the regular cycle. The door light doesn't lit... The switch doesn't work, DEAD! Any other suggestions? It just ignoring, was so proud when I fixed it.
|
NCSU_laundry_tech
Sublime Master of Appliantology
| Joined: | Mon Aug 18th, 2008 |
| Location: | Raleigh, North Carolina USA |
| Posts: | 223 |
| Flavorite Brew: | The one in my hand |
| Status: |
Online
|
|
Posted: Thu Oct 9th, 2008 00:27 |
|
dispenser drawer reed switch or door switch perhaps
____________________
To alcohol! The cause of... and solution to... all of life's problems.
Doc Watson - Shady Grove: http://www.youtube.com/watch?v=b-kaG1NuLZM
riding my dirtbike in clayton NC: http://www.youtube.com/watch?v=NnCmY0vzmYM
|
edcmaak11
Apprentice Appliantologist
| Joined: | Sat Mar 22nd, 2008 |
| Location: | NYC, New York USA |
| Posts: | 24 |
| Flavorite Brew: | All beers.... |
| Status: |
Offline
|
|
Posted: Thu Oct 9th, 2008 17:25 |
|
lol, just checked the power outlet went out... Rerouted to other outlet, is running...
Only 1 problem, the Fabric softner either still stay in dispensing tray or left with water after the 2 washes. Could it be clogged?
Last edited on Thu Oct 9th, 2008 17:33 by edcmaak11
|
Current time is 20:02 | |
|
