| Author | Post |
|---|
The Unwashed Mass
Apprentice Appliantologist
| Joined: | Fri Aug 15th, 2008 |
| Location: | |
| Posts: | 3 |
| Flavorite Brew: | Paulaner dunkel |
| Status: |
Offline
|
|
Posted: Sat Aug 16th, 2008 04:56 |
|
I just replaced the timer on my washer, but now the timer dial won't advance to the next phase of the wash cycle.
When I ran a test wash, I moved the dial to normal wash, and was pleased to see beautiful water filling the tub. However, the water doesn't stop. The dial doesn't rotate to next cycle and simply stays at the beginning click of the dial.
Any suggestions? When I replaced the timer, did I screw the dial too tight? Wires not hooked back up corectly? And by "I", I mean my competent friend.
Note: The timer knob is busted. I hand crank the dial. That's what I think caused the whole problem in the first place. The washer was constantly powered, and I would race across the contacts reaching the desired cycle. Burning smell and eighty bucks later, I figure I am one step away.
Thanks.
Last edited on Sat Aug 16th, 2008 14:12 by The Unwashed Mass
|
nickfixit
Fellow, Academy of Sublime Masters of Appliantology
| Joined: | Tue Apr 26th, 2005 |
| Location: | Luna Pier, USA |
| Posts: | 1349 |
| Flavorite Brew: | Samuel Adams |
| Status: |
Offline
|
|
Posted: Sat Aug 16th, 2008 12:14 |
|
Check the hose that runs from the water level switch to a fitting on the side of the tub. It may be dissconected on one end.
Nick
____________________
" Giving numerical data to Sears management is like giving a monkey a machine gun. No one knows for certain what will happen, but you can be sure of two things... It will be real messy, and only the monkey will be unharmed"
|
The Unwashed Mass
Apprentice Appliantologist
| Joined: | Fri Aug 15th, 2008 |
| Location: | |
| Posts: | 3 |
| Flavorite Brew: | Paulaner dunkel |
| Status: |
Offline
|
|
Posted: Sat Aug 16th, 2008 16:03 |
|
Brilliant,Nick! I had left the hose disconnected.
Do I need to prime it in any way, or is it ready now it is reconnected?
How does that work? Does it detect a vacuum? Barometric?
Also, if you have any experience with these models, should I plan on buying a new unit soon? It came with the house and has been quite reliable. I would prefer to maintain it if cost effective.
Thank you again.
|
Pegi
Fellow, Academy of Sublime Masters of Appliantology
| Joined: | Tue May 3rd, 2005 |
| Location: | Wichita Falls, Texas USA |
| Posts: | 12446 |
| Flavorite Brew: | Sweet Iced Tea |
| Status: |
Online
|
|
Posted: Sat Aug 16th, 2008 18:27 |
|
| Air pressure trips the fill level switch thru that hose, to be sure it is reset drain the washer and let it spin, then try it again, if that pressure switch does not close to give power to the timer it never will advance nor will you get agitation...
____________________
Moderator & Assistant Admin. for Servicetechhelp Associaton, Inc.
http://www.servicetechhelp.com
STH HELPDESK URL.... http://www.servicetechhelp.com/h2desk/
________________________________________________
For my Friend Gordon- http://serviceeveryday.com
|
nickfixit
Fellow, Academy of Sublime Masters of Appliantology
| Joined: | Tue Apr 26th, 2005 |
| Location: | Luna Pier, USA |
| Posts: | 1349 |
| Flavorite Brew: | Samuel Adams |
| Status: |
Offline
|
|
Posted: Sun Aug 17th, 2008 00:46 |
|
At least it was a cheap fix, zero cost is always cool. Pegis' explaination is right on the money. It's a good washer, I would expect good service from it.
Nick
____________________
" Giving numerical data to Sears management is like giving a monkey a machine gun. No one knows for certain what will happen, but you can be sure of two things... It will be real messy, and only the monkey will be unharmed"
|
The Unwashed Mass
Apprentice Appliantologist
| Joined: | Fri Aug 15th, 2008 |
| Location: | |
| Posts: | 3 |
| Flavorite Brew: | Paulaner dunkel |
| Status: |
Offline
|
|
Posted: Sun Aug 17th, 2008 19:48 |
|
Thank you both so much. The washer is running like a charm.
|
Current time is 21:15 | |
|
