|
FAQs | Parts | Service | Store | Newsletter | Sitemap | Beer | Fixitnow.com |
ApplianceGuru.com: The Samurai Appliance Repair Forums > Do-It-Yourself Appliance Repair Help > Heating, Ventilation, and Air Conditioning (HVAC) > Getting a Code 31 Error on Furnace model No. GB3AAV |
Konnichiwa and Welcome!Please register to post a question. It's FREE!
|
| Moderated by: RegUS_PatOff, hvacdrd, applianceman18007260692 |
|
Page:   1 2 |
|
||||||||||||
| Getting a Code 31 Error on Furnace model No. GB3AAV | Rate Topic |
| Author | Post |
|---|
| Posted: Sat Dec 13th, 2008 09:00 pm |
|
21st Post |
|
RegUS_PatOff Fellow, Academy of Sublime Masters of Appliantology 
|
I'm not a HVAC expert... are there any such numbers on your board ?
____________________ RegUS_PatOff http://www.youtube.com/watch?v=oPAY2LsKVEw my video production: “Easter Seals Walk With Me” (also in HQ) http://www.youtube.com/watch?v=-EBiLyYXMiA Upon leaving this Earth "Do you want the Smoking or Non-Smoking section ?" |
||||||||||||||
| |||||||||||||||
| Posted: Sat Dec 13th, 2008 10:03 pm |
|
22nd Post |
|
ccmulder Senior Apprentice Appliantologist
|
RegUS_PatOff wrote: I'm not a HVAC expert... I would have to take it out to see the model number--I can't see it from the outside.
|
|||||||||||||
| ||||||||||||||
| Posted: Sun Dec 14th, 2008 12:26 am |
|
23rd Post |
|
applianceman18007260692 Sublime Master of Appliantology 
|
make sure all the board connections are tight and free of corrosion.
____________________ "May the hinges of our friendship never grow rusty" Old Irish Saying |
||||||||||||||
| |||||||||||||||
| Posted: Mon Dec 15th, 2008 01:24 pm |
|
24th Post |
|
ccmulder Senior Apprentice Appliantologist
|
Well, the problem is a soldered conneciton--I Googled and found there to be a problem with these boards in that regard. Right now its wording fine with a wedged piece of wood (covered in Tin Foil) pressing against the Board Plug, which is keeping the contact. I'll take it out and take a look at it once this current cold wave (relative since I am here in Southern California) snaps.
|
|||||||||||||
| ||||||||||||||
| Posted: Mon Dec 15th, 2008 01:32 pm |
|
25th Post |
|
RegUS_PatOff Fellow, Academy of Sublime Masters of Appliantology
|
Milwaukee, Wisconsin +6 F but we have power, not like the Northeast  Last edited on Mon Dec 15th, 2008 01:52 pm by RegUS_PatOff ____________________ RegUS_PatOff http://www.youtube.com/watch?v=oPAY2LsKVEw my video production: “Easter Seals Walk With Me” (also in HQ) http://www.youtube.com/watch?v=-EBiLyYXMiA Upon leaving this Earth "Do you want the Smoking or Non-Smoking section ?" |
||||||||||||||
| |||||||||||||||
| Posted: Tue Dec 16th, 2008 09:32 pm |
|
26th Post |
|
ccmulder Senior Apprentice Appliantologist
|
Wondering if anyone knows where the hell the Model Number is on my Heater--i looked all over on the inside of the panel and can't find one.
|
|||||||||||||
| ||||||||||||||
| Posted: Fri Dec 26th, 2008 03:21 pm |
|
27th Post |
|
ccmulder Senior Apprentice Appliantologist
|
Well wanted to let everyone know it was the main Controller Board on the heater that was the problem--replaced it and its been working fine.
|
||||||||||||||
| |||||||||||||||
| Posted: Fri Dec 26th, 2008 03:22 pm |
|
28th Post |
|
ccmulder Senior Apprentice Appliantologist
|
Well wanted to let everyone know it was the main Controller Board on the heater that was the problem--replaced it and its been working fine.
|
|||||||||||||
| ||||||||||||||
| Posted: Fri Dec 26th, 2008 05:40 pm |
|
29th Post |
|
ROBBYRIG Sublime Master of Appliantology 
|
I think there's an echo in this thread.
|
||||||||||||||
| |||||||||||||||
| Current time is 01:38 am | Page: 1 2 |
| ApplianceGuru.com: The Samurai Appliance Repair Forums > Do-It-Yourself Appliance Repair Help > Heating, Ventilation, and Air Conditioning (HVAC) > Getting a Code 31 Error on Furnace model No. GB3AAV | Top |
FAQs | Parts | Service | Store | Newsletter | Sitemap | Beer | Fixitnow.com
