|
|
Air Conditioners | Dehumidifiers | Dishwashers | Disposals | Dryers | Freezers | Humidifiers | Ice Makers | Microwave Ovens | Ovens, Ranges, Stoves | Refrigerators | Trash Compactors | Washers | Water Filters |
|
FAQs | Contact | Apprenticeship | Consultations | Parts | Model Number Help | Newsletter | Beer | Fixitnow.com
|
ApplianceGuru.com: The Samurai Appliance Repair Forums > Do-It-Yourself Appliance Repair Help > The Kitchen Appliance Repair Forum > GE Refrigerator/Freezer PTS 25 LBM |
|
| Moderated by: BrntToast, RegUS_PatOff, appl.tech.29501 | Search Our Sites for More Info! |
|
|||||||||||||
| GE Refrigerator/Freezer PTS 25 LBM | Rate Topic |
| Author | Post |
|---|
| Posted: Mon Apr 4th, 2005 04:01 am |
|
1st Post |
|
ckamimura Senior Apprentice Appliantologist
|
Yeah, the usual complaint is that the freezer is too warm. Freezer on top and Frig. on the bottom. Lots of frost on the meat and stuff. Thermometer measures about -10 degrees below 0. Reduced the freezer digital control from a 5 to a 3. Still too cold. Refrigerator temperature okay. Any ideas? Bought this thing a little over a year ago. Yeah, out of warrantee. Just my luck! Should have bought an Amana. Chuck 
|
||||||||||||||
| |||||||||||||||
| Posted: Mon Apr 4th, 2005 08:08 am |
|
2nd Post |
|
Samurai Appliance Repair Man Fermented Grand Master of Appliantology 
|
The problem isn't that the freezer is too cold, it's that too much moisture is entering either the freezer or fresh food compartment and condensing as frost on your food. You don't want the freezer to be any warmer than +5F, if you're getting -10F, then consider yourself lucky. Check your door gaskets carefully. This requires keen powers of observation. Many times, I'll go to a house with this exact problem and it always turns out to be a door sealing problem. They never believe me until I fix it and the problem goes away. On a new fridge like yours, I'd suspect that the cabinet isn't square and this is creating a gap somewhere in the sealing surface.
____________________ To ask a question, use our new forums==> http://appliantology.org 365-Day No-Hassle Return Policy on all parts purchased through this site, even electrical parts that have been installed! |
|||||||||||||
| ||||||||||||||
| Posted: Mon Apr 4th, 2005 05:34 pm |
|
3rd Post |
|
Mad Mac Fellow, Academy of Sublime Masters of Appliantology 
|
Samurai Appliance Repair Man wrote:On a new fridge like yours, I'd suspect that the cabinet isn't square and this is creating a gap somewhere in the sealing surface. Samurai, I've ran into this very issue with GE products in the past. It's certainly worth checking.
____________________ Mad Mac....Pray to God he's out there....somewhere. |
||||||||||||||
| |||||||||||||||
| Posted: Tue Apr 5th, 2005 04:48 am |
|
4th Post |
|
denrayr Fellow, Academy of Sublime Masters of Appliantology 
|
ge had a couple of top mount models with airflow problems. the fix was to replace the evap cover with a revised one along with a revised mother board. i think the new mother board forced the fan to run a little faster.
____________________ RedRock Appliance Service 435-773-7838 http://www.redrockrepair.com Serving St George and Southern Utah |
|||||||||||||
| ||||||||||||||
| Posted: Wed Apr 6th, 2005 12:14 am |
|
5th Post |
|
ckamimura Senior Apprentice Appliantologist
|
Arigato for the explanation on my freezer problem. I don't quite understand why my freezer temp went from 0 to -10. Would air leak around the gasket cause this? Would a bad defrost heater cause this frost buildup if my gaskets are okay? What about a bad thermostat allowing the compressor to run longer than it should. Would that lower my freezer temp? Arigato again! Chuck
|
||||||||||||||
| |||||||||||||||
| Posted: Wed Apr 6th, 2005 01:37 am |
|
6th Post |
Jedi Appliance Guy
|
It couldn't hurt to turn that thing off at the breaker for an hour. Won't cost ya nut'n. That fridge doesn't have a thermostat. It's a computer running a program. Always allow 24 hours for temps to stabilize every time you adjust the temperature. Last edited on Wed Apr 6th, 2005 01:38 am by Jedi Appliance Guy |
|||||||||||||
| ||||||||||||||
| Posted: Wed Apr 6th, 2005 03:17 am |
|
7th Post |
|
The Seven Master Appliantologist
|
ckamimura wrote:Lots of frost on the meat and stuff. Thermometer measures about -10 degrees below 0. Reduced the freezer digital control from a 5 to a 3. Still too cold. Refrigerator temperature okay. Does your GE fridge have "Upfront Electronic Digital Display which displays exact temperatures for the fresh food and freezer compartments"? If so, this fridge has electronic temperature sensors (NTC themistors) and electronic control board instead of mechanical thermostat. The "electronic control" fridge usually controls the temp of the fresh food and the freezer independantly by 2 thermistors. In your case, the "freezer" thermistor could be bad (either short-circuit or out-of-range) The "frost" water could get into the "freezer" thermistor if the thermistor is "crack" and it will cause a "short-circuit". The control board thinks the freezer is not cold enough and continue to cool it to an abnormal low temp. You may have to check the "freezer" thermistor according to the specification from GE manual.
____________________ The Seven |
||||||||||||||
| |||||||||||||||
| Posted: Wed Apr 6th, 2005 03:36 am |
|
8th Post |
Jedi Appliance Guy
|
The force is strong in this one. Hmmm.. Water/Ice/Moisture in the evaporator thermistor. For years Good A/C techs have been installing "drip loops" in their fan motor wires to keep water from following the wire into the motor. Might not be a bad idea look for, and add as needed to the evap thermistor, every time you have the evaporator cover removed. Last edited on Wed Apr 6th, 2005 03:38 am by Jedi Appliance Guy |
|||||||||||||
| ||||||||||||||
Current time is 07:14 pm
|
|
| ApplianceGuru.com: The Samurai Appliance Repair Forums > Do-It-Yourself Appliance Repair Help > The Kitchen Appliance Repair Forum > GE Refrigerator/Freezer PTS 25 LBM | Top |
| Find Appliance Parts & Diagrams Here |
| Enter a model number, part number, type of appliance, brand, or even a part description. |
|
365-day return policy on all parts ordered through this site! |
FAQs | Contact | Apprenticeship | Consultations | Parts | Model Number Help | Newsletter | Beer | Fixitnow.com
